Car diagnostic tools information by obd2tool: 八月 2020

2020年8月25日星期二

How to Solve Lonsdor K518 Device Fault20 Error

Error: It prompts “Device fault20” on Lonsdor K518 programmer

Solution:
Step 1: Hold those two buttons marked in red at the same time

Then you will enter the Update interface as below

Step 2: Press “Uninstall APK” once, and you will get the prompt as below

Step 3: Press “OK” and you will enter the Update interface again.

Step 4: Press “Oldest APK” once and you will see loading interface

step 5: Enter the password

Step 6: Connect the device to WiFi and then press “Update”

Step 7: Press “OK” to update the device

When finish the steps above, the K518 key programmer will be normal as before after updating.

Note: this solution is also suitable for the following common problems:
Problem 1: Cannot enter the main interface of K518 device
Problem 2: It takes much time to enter the main menu of K518
Problem 3: Some menus are lost in the K518 device

How to Solve Ford VCM II IDS V108 Application Error 27076

I have installed IDS V108 on Vmware to work with my Ford VCM II. When I run the software, I get the application error 27076 message “Ghost has detected corruption in the image file. Please perform an integrity check on the image…” is shown as below.

The possible cause:

Maybe there is something wrong with the file.

The solution:

Uninstall the current software and install by the following download link.

https://share.weiyun.com/5S508ie

Password: ynd37s

Security: Yes, it has been tested 100% ok by engineer.

Operating system: You’d better install Ford IDS V108 on Win7

Recommend WIN7 32bit system download link:

https://share.weiyun.com/59Noy7p

Password: 0awk7b

Computer operating system requirements:

1.If your computer hard drive only has one partition, please prepare a 16GB U flash drive

2.If has 2 partitions, please unzip the software into any other partition except disk C.

Guide to install Ford IDS V108 software for VCM2:

Extract Ford 108 software, delete the redundant files

Click on GHOST 8.0 to one key recovery

Restart computer

Click on Ford extending programming

Find VCI Manager (Ford-VCM-II) to install

If it prompts “PC software initialization error (getmoduletype), please go to Computer-> program files-> Ford motor company-> IDS-> Runtime-> install3rdparty-> ETAS-> setup

Install Bosch VCI Manager

When install successfully, run VCI Manager (Ford-VCM-II)

Connect VCMII to computer as below

Go to computer management-> Device manager->Network adapters to check whether the device connect successfully

Make sure the Internet connection is normal

Then you can run IDS 108 software

2020年8月10日星期一

How to Virgin VGS2 TCU Mercedes 722.9 via Vediamo

Question:

any one know source for 7G programming and scn coding by vin number, i use vediamo .

It uses VGS then i need to make it virgin before doing any coding and programming.

I heard vediamo can make it virgin for vgs2. Could you explain how you virginize VGS2 via vediamo ?

Solution:

Device required:
Vediamo 04.02.02 and Mb Star C3 chinese MUX or
Vediamo 05.00.05 and chinese SD Connect C4
Modified CBF file with according script file (google search for CBF file)

Method:
works on bench and OBD2 connector.

Procedure:

For example: TCU’s with part number A 033 545 73 32

To play with it, just copy VGSmod2.cbf into directory, in which you keep all your cbf. files.

Usually per default it should be: C:\Documents and Settings\All Users\Application Data\Vediamo\VediamoData.

Than open Vediamo, choose the VGSmod2.cbf and load it. In this moment a new subdirectory named “VGSmod2” should be created in ..\VediamoData.

Copy unpacked VGS2-Virgin.xml script into this subdirectory. Now preparation is finished.

To erase personalisation keys from 7G-Tronic VGS2 just establish connection to TCU, go to Sequences, press Execute Sequence (not OPEN, just EXECUTE!) , choose and start VGS2-Virgin.xml and follow the steps.

Note:

You are at you risk.

Once TCU is virgin (some areas of EEPROM memory are erased) it must be prepared to be used in next car. Depending of software version and EEPROM memory layout, virginising can (but not always have to) erase also VIN, CALID, Shift lever learning values or SCN. All this need to be performed after reusing TCU on different car.

THERE IS NO NEED TO PERSONALIZE AND ACTIVATE your TCU to make it work.

This 722.9 VGS units will work well even without performing that steps. All VGS (Gen 1,2,3) using FBS3 immobiliser system will activate and personalize automatically after 300 ignition cycles. No additional actions are needed. To use your virginized TCU on any Mercedes 722.9 Gearbox, you need to be sure than actual software version fit this car (VIN) with this valve body (EHS number) and Coding is equal to destination car equipment. If software version is not right, some codings can be refused. It is always recommended to reflash the unit after virginizing to restore its EEPROM layout and perform software update.

Solved! MB SD C4 “00” Icon and Initialization Multiplexer Failed

I got the MB SD C4 Xentry and EVG7 tablet full kit. EVG7 displays “00” icon on Toolbar. Also failed to configure SD C4 main unit. How can i fix it?

Xentry Software displays error:

Initialization of diagnosis multiplexer failed

obd2tool.com engineer working solution:

Run an sd connect c4 firmware update:

Go to C:\Program Files\Mercedes-Benz\SDConnect Toolkit, change update_automaticx, update_manualx and update_specicalx 3 files to update_automatic, update_manual and update_specical (delete the x letter).

Go to C:\Program Files\Softing\Diagnostic Tool Set 8\8.03\Interfaces\DCDI_DPduApi\eCOM_Toolkit, change update_automaticx, update_manualx and update_specicalx files to update_automatic, update_manual and update_specical (delete the x letter)